HomeMy WebLinkAboutHandouts_Selection Review_8/21/2024 Division of Zabatt,Incorporated
4612 Highway Avenue
-- Jacksonville,FL 32254
Z A B A T T PH: 9043844505
FX: 904 394 7446 7446
POWER SYSTEMS
CBC#1257077
Jacksonville Orlando Tampa
08/13/2024
RE: Exhibit B-Village of Tequesta RFP-PW-03-05-2024/DC
Contractor Narrative/Drawing:
• The proposed Gillette Generator will meet all project generator specifications,
communication capabilities, and control specifications. We are supplying the same
generator set package as shown in Addendum No. 2 dated August 01, 2024.
• Suburban Propane will be our sub-contractor to supply & install the (2)1000gal
underground propane tanks. They will also be contracted to install & plumb all the
necessary fuel piping, regulator, etc.
• We are proposing to install a Thomson TS870 series Service Entrance rated automatic
transfer switch rated 600A. Installation will be near the Utility Transformer.
• The ATS will be between the Utility Transformer and the 600A MDP. This will allow the
Generator Set system to back-up 100% of the service.
• The proposed Generator Set location will be at the parking lot about 40ft from the
electrical/mechanical room. The exhaust discharge will be in the same location as the
radiator air discharge and will be in a vertical air discharge direction.
• The ATS is currently estimated at 18-20 weeks lead time after approved submittals. The
generator is about 8-10 weeks lead time after approved submittals. Engineering &
permitting can begin after receipt of purchase order. To start construction, we will
need the ATS to be delivered. We will be needing about 60days to completion after
construction begins. Overall expectations is 8-9months after purchase order, approved
submittal, & approved permits.
• Our Electrical Engineer will ensure electrical compliance.
• Our BID proposal includes a proposed layout drawing showing the Generator Set, LP
Tanks, and ATS locations. See Attached.
Edwin Vergara
Sales Support Engineer
904-423-5750
edwin.vergara@zabatt.com
o n I >
m
g
m
nm
m
O
m r r l
n
z -
m
Nil
�c
_g �a
;q € N
4 � i�gTt
222222 4
ExEEHOTECTIOH EEYOBd QTl U
PALM
FCACK, *ID
.CHZNHIL AALUI—
VIllAGEOFTEQUES TA ---
p TEQUESTA YLLLAGE HALL TEQUaGYHAAGE HALL.
`J SITE FIRE PROTECTION PLAN nsri�AUMVE Lu« a+wnnnrwn _
■+ TEQUMA,MORM eFw�wm*a�nuc rn uVE �Evmx ex
II ftOariwE a R I
TAt fK. AR9
pppA�¢A� �rq<L&GOOOEAW ygp�cy�Goc.yuc� E v%x
ISSt!® avaK
EORB�J111E U,7Eos HUEF6000.BnS �MLLAO•IDTWE®RN1bEtlt w
XcTlEltwoKT A1N01lT1NEYWIi[a1NlcUR1t141OF flODLL FpW�^'
/Ao'�A GILLETTE
ks!.,ov/ GENERATORS 60 HZ MODEL
SP-960
LIQUID COOLED NAT. GAS ENGINE GENERATOR SET
STANDBY
Model 120-C RISE
HZ LPG N.G.
SP-960 60 HERTZ 60 80 95/96 _
® V
I BUILT
�IN THE a** All generator sets are USA prototype built and thoroughly tested. s -
Production models are USA factory built and 100%load tested.
"OPEN"GEN-SET
US UL2200, UL1446, UL508, U
C U� L142, UL498 There is no enclosure, so gen-set must be
placed within a weather protected area,
un-inhabited by humans or animals, with
1 NFPA 110, 99, 70, 37 proper ventilation. Silencer not supplied,
All generator sets meet NFPA-110 Level 1, when equipped with the as installation requirements are not
NFPA necessary accessories and installed per NFPA standards. known. However, this item is available as
optional equipment.
n c NEC 700, 701, 702, 708 — --
NEMA ICS10, MG1, ICS6, AB1
ANSI C62.41, 27, 59, 32, 480, 40Q, 81U, 360-05
,SCE ASCE 7-05 & 7-10
"LEVEL 2"HOUSED GEN-SET
All generator sets meet 180 MPH rating.g g Full aluminum weather protection and superior
sound attenuation for specific low noise
A applications.Critical grade muffler is standard.
\�/EPQ EPA 40CFR Part 60, 1048, 1054, 1065, 1068
GENERATOR RATINGS LIQUID PROPANE GAS FUEL NATURAL GAS FUEL
GENERATOR MODEL VOLTAGE PH HZ 1200C RISE STANDBY RATING 1200C RISE STANDBY RATING
L-N L-L KW/KVA AMP KW/KVA AMP
SP-960-1-1 120 240 1 60 1 80/80 333 95/95 396
SP-960-3-2 120 208 3 60 801100 278 96/120 334
SP-960-3-3 120 240 3 60 80/100 241 96/120 289
SP-960-3-4 277 480 3 60 80/100 120 96/120 145
SP-960-3-5 127 220 3 60 80/100 263 1 96/120 315
SP-960-3-16 346 600 3 60 80/100 96 1 96/120 115
RATINGS: All single phase gen-sets are dedicated 4 lead windings,rated at unity(1.0)power factor. All three phase gen-sets are 12 lead windings,rated at.8 power factor
120°C"STANDBY RATINGS"are strictly for gen-sets that are used for back-up emergency power to a failed normal utility power source. This standby rating allow:
varying loads,with no overload capability,for the entire duration of utility power outage. All gen-set power ratings are based on temperature rise measured by resistance
method as defined by MIL-STD 705C and IEEE STD 115,METHOD 6.4.4. All generators have class H(180°C)insulation system on both rotor and stator windings. Al
factory tests and KW/KVA charts shown above are based on 120°C(standby)R/R winding temperature,within a maximum 40°C ambient condition. Generators operated ai
standby power ratings must not exceed the temperature rise limitation for class H insulation system,as specified in NEMA MG1-22.40. Specifications&ratings are subject
to change without prior notice.
Gillette Generators,Inc.-2921 Thorne Dr.-Elkhart,IN 946514-Ph:574-264-9639*Fax:574-262-1840 e Web:www.gillettegencrators.com e spc4-221103 1
APPLICATION AND ENGINEERING DATA FOR MODEL SP-960-60 HZ
GENERATOR SPECIFICATIONS GENERATOR FEATURES
Manufacturer...................................Stamford Electric Generators • World Renown Stamford Electric Generator having UL-1446
Model&Type...........UCI274D-06,4 Pole,4 Lead,Single Phase certification.
.......UCI274D-311,4 Pole, 12 Lead re-connectable,Three Phase • Full generator protection with Deep Sea 7420 controller,
........................UCI274C-17,4 Pole,6 Lead,600V,Three Phase having UL-508 certification.
Exciter.....................................................Brushless,shunt excited * Automatic voltage regulator with over-excitation, under-
Voltage Regulator.......................................Solid State,HZ/Volts frequency compensation, under-speed protection, and EMI
Voltage Regulation................................'/z%,No load to full load filtering. Entire solid-state board is encapsulated for
Frequency................................Field convertible,60 HZ to 50 HZ moisture protection.
Frequency Regulation.............'/z%('/z cycle,no load to full load) • Generator power ratings are based on temperature rise,
Unbalanced Load Capability.....................100%of standby amps measured by resistance method, as defined in MIL-STD
One Step Load Acceptance.................100%of nameplate rating 705C and IEEE STD 115,Method 6.4.4.
Total Stator and Load Insulation...........................Class H, 180°C a Power ratings will not exceed temperature rise limitation for
Temperature Rise......... 120°C R/R,standby rating @ 400C amb. class H insulation as per NEMA MG1-22.40.
10 Motor Starting @ 30%Voltage Dip(240V)............360 kVA e Insulation resistance to ground,exceeds 1.5 meg-ohm.
3 0 Motor Starting @ 30%Voltage Dip(208-240V).....400 kVA . Stator receives 2000 V. hi-potential test on main windings,
3 O Motor Starting @ 30%Voltage Dip(480V)............520 kVA and rotor windings receive a 1500 V.hi-potential test,as per
3 O Motor Starting @ 30%Voltage Dip(600V)............445 kVA MIL-STD 705B.
Bearing.....................................................1,Pre-lubed and sealed . Full amortisseur windings with UL-1446 certification.
Coupling..........................................................Direct flexible disc . Complete engine-generator torsional acceptance, confirmed
Total Harmonic Distortion...............Max 3�/2%(MIL-STD705B) during initial prototype testing.
Telephone Interference Factor............Max 50(NEMA MG1-22)
Deviation Factor.................................Max 5%(MIL-STD 405B) • Full load testing on all engine-generator sets,before shipping.
Ltd.Warranty Period..............24 Months from date of start-up or • Self ventilating and drip-proof&revolving field design
.......................................................1000 hours use,first to occur.
ENGINE SPECIFICATIONS AND APPLICATIONS DATA
ENGINE FUEL CONSUMPTION
Manufacturer......................................Power Solutions,Inc.(PSI) LP GAS:FT3/HR(M3MR) STANDBY
Model and Type................Ind,Power Train,5.7LTCAC,4 cycle 100%LOAD 511 14.6
Aspiration.............................Turbocharged/Charged Air Cooled 75%LOAD 410 11.5
Cylinder Arrangement.........................................8 Cylinders,V-8 50%LOAD 290(8.3)
Displacement Cu.In.(Liters).......................... 350(5.7) LPG=2500 BTU X FT'/HR=Total BTU/RR
"' 3.4 ( LPG Conversion:8.50 FT'=I LB.:36.4 FT'=1 GAL.
Bore&Stroke In.(Cm.).............................4.0 x 3.48(10.1 x 8.8)
Compression Ratio................................................................9.4:1 NAT.GAS:FT3/HR(M3MR) STANDBY
Main Bearings&Style...............................5,M400 Copper Lead 100%LOAD 1212 34.4
Cylinder Head.................................................................Cast Iron 75%LOAD 990 28.1
Pistons..................................................................Cast Aluminum 50%LOAD 686 19.5
Crankshaft.................................................................Nodular Iron NG=1000 BTU X FT'/HR=Total BTU/RR
Exhaust Valve.........................................................Inconel,A193 OIL SYSTEM
Governor.......................................................................Electronic
Frequency Reg.(no load-full load)............................Isochronous Type Full Pressure
Frequency Reg.(steady state)............................................t 1/4% .......................(L)...........................................
Oil Pan Capacity qt. (L) 8.0(7.6)
Air Cleaner.........................................Dry,Replaceable Cartridge
Oil Pan Cap.W/filter qt.(I) 8.5(8.0)
Engine Speed 1800 rpm ...........................................
................. in)....................... ................ Oil Filter.................................................. 1,Replaceable Spin-On
Piston Speed,ftlmin(m./min)....................... ................870(265)
Max Power,bhp(kwm)Standby/LPG........ ................145(108) ELECTRICAL SYSTEM
Max Power,bhp(kwm)Standby/NG.......... ................155(115) Ignition System.............................................................Electronic
Ltd. Warranty Period....... 12 Months or 2000 hrs.,first to occur
Eng.Alternator and Starter:
FUEL SYSTEM Ground...................................................Negative
Volts,DC.........................................................12
Type................................LPG or NAT.GAS,Vapor Withdrawal Recommended Battery to-18"C(0°F):... 12 VDC,Size BCI#27,
Fuel Pressure(kpa),in.H2O* .........................0.74-2.74),7"-11" Max Dimensions: ........12" lg X 6 3/4"wi X 9"hi,with standard
Secondary Fuel Regulator...................NG or LPG Vapor System round posts. Min output at 700 CCA. Battery tray(max.dim.at
Auto Fuel Lock-Off Solenoid........................Standard on all sets 12"lg x 7"wi), hold down straps, battery cables, and battery
Fuel Supply Inlet Line..................................................1'/4"NPTF charger, is furnished. Installation of (1) starting battery is
*Measured at gen-set fuel inlet,downstream of any dry fuel required, with possible higher AMP/HR rating, as described
accessories above,if normal environment averages-13°F(-25°C)or cooler.
2 Gillette Generators,Inc.9 2921 Thorne Dr.•Elkhart,IN*46514•Ph:574-264-9639*Fax:574-262-1840•Web:www. ilg lettegenerators.com•spc4-221103
APPLICATION AND ENGINEERING DATA FOR MODEL SP-960-60 HZ
COOLING SYSTEM SOUND LEVELS MEASURED IN dB(A)
Type of System................................Pressurized,closed recovery Open Level 2
Coolant Pump.....................................Pre-lubricated,self-sealing Set Encl.
Cooling Fan Type(no.of blades).................................Pusher(7) Level 2,Critical Silencer.........................87............ ...........80
Fan Diameter inches(cm)..............................................26"(660) Level 3,Hospital Silencer........................................ ...........75
Ambient Capacity of Radiator°F(°C)..........................125(51.6)
Engine Jacket Coolant Capacity Gal(L)........................3.6(13.7) Note: Open sets (no enclosure) have silencer system choices due to
Radiator Coolant Capacity L .................5.4 20.4 unknown job-site applications. Level 2 enclosure has installed critical
p Gal. ( ) ( ) silencer with upgrade to Level 3 hospital silencer. Sound tests are
Maximum Restriction of Cooling Air Intake averaged from several test points and taken at 23 ft. (7 in) from source
and discharge side of radiator in.H2O(kpa).................... .5(.125) of noise at normal operation.
Water Pump Capacity gpm(L/min).............. .................39(147)
Heat Reject Coolant: Btu/min(kw).............. ..............6300(111) DERATE GENERATOR FOR ALTITUDE
Low Radiator Coolant Level Shutdown...................Standard
Note:Coolant temp.shut-down switch setting at 212T(100'Q with 50150 3%per 1000 ft.(305m)above 3000 ft. (914m)from sea level
(water/antifreeze)mix.
DERATE GENERATOR FOR TEMPERATURE
COOLING AIR REQUIREMENTS 2%per 10°F(5.6°C)above 104°F(40°C)
Combustion Air,cfin(m3/min) ..............................263 (7.1)
Radiator Air Flow cfin(m3/min)................... ............10800(306) DIMENSIONS AND WEIGHTS
Heat Rejected to Ambient:
Engine:kw(btu/min)............................. ................50(2844) Open Level 2
Alternator:kw(btu/min)........................ ...............14.5 (825) Set Enclosure
Length in(cm)..........................98(248)...... ................122(310)
EXHAUST SYSTEM Width in(cm)...........................48(122)...... .................48 (122)
Height in(cm)..........................64(163)...... .............. 72.5 (183)
Exhaust Outlet Size....................................................................3" 10 Net Weight lbs(kg).........2229(1011)...............3049(1383)
Max.Back Pressure in.hg(KPA).................................3.0(10.2) 10 Ship Weight lbs(kg).......2419(1037)... ............3299(1496)
Exhaust Flow,at rated kw:cfm(m3/min)..... ................. 846(24) 30 Net Weight lbs(kg)..........2096(951) .... ............2916(1323)
Exhaust Temp.,at rated kw:°F(°C)............. ..............1250(677) 30 Ship Weight lbs(kg).......2286(1037)... ............3166(1436)
Engines are EPA certified for LPG&Natural Gas.
DEEP SEA 7420MKII DIGITAL MICROPROCESSOR CONTROLLER
Deep Sea 7420N KU
The "7420MKH" controller This controller includes the expansion features including RS232,
is an auto start mains RS484 (using MODBUS-RTU/TCP), direct USB connection
(utility) failure module for with PC, expansion optioned using DSENet for remote
single gen-set applications. annunciation and remote relay interfacing for a distance of up to
This controller includes a 3300FT. The controller software is freely downloadable from
backlit LCD display which the internet and allows monitoring with direct USB cable, LAN,
continuously displays the or by internet via the built in web interface.
status of the engine and
generator at all times. Advanced Features:
The "7420MKII" controller will also monitor speed, frequency, PLC editor allow user configurable functions to meet specific
voltage, current, oil pressure, coolant temp., and fuel levels. application requirements • Data logging to assist with fault
These modules have been designed to display warning and shut finding with 20 parameter data logging and recording on USB
down status. It also includes: (11) configurable inputs • (8) drives • Multiple date and time scheduler • Set maintenance
configurable outputs • voltage monitoring • mains (utility) periods can be configured to maintain optimum engine
failure detection • (250) event logs • configurable timers • performance • Modules can be integrated into building
automatic shutdown or warning during fault detection • remote management systems (BMS) using MODBUS • Configurable
start(on load)•engine preheat•advanced metering capability • MODBUS pages with RTU& TCP support•Fully configurable
hour meter • text LCD 132 x 64 pixel ratio display • protected via DSE Configuration Suite PC software • Remote SCADA
solid state outputs •test buttons for: stop/reset•manual mode• monitoring via DSE Configuration Suite PC software • Engine
auto mode • lamp test • start button • power monitoring (kWh, exerciser•Automatic load transfer•Multiple configurations
kVAr,kVAh,kVArh)•IP65 rating(with supplied gasket)
Gillette Generators,Inc.9 2921 Thorne Dr.-Elkhart,IN*46514•Ph:574-264-9639*Fax:574-262-1840•Web:www. ilg leuegencrators.com•spc4-221103 3
STANDARD FEATURES FOR MODEL SP-960-60 HZ
STANDARD FEATURES
CONTROL PANEL: AC GENERATOR SYSTEM:
Deep Sea 7420 digital microprocessor with AC generator • Shunt excited • Brushless design • Circuit
logic allows programming in the field.Controller has: Breaker installed and wired to gen-set • Direct connection
• STOP-MANUAL-AUTO modes and automatic engine to engine with flex disc • Class H, 180°C insulation a Self
shutdowns,signaled by full text LCD indicators: ventilated•Drip proof construction•UL Certified
• Low oil pressure • Engine fail to start
• High engine temp • Engine over speed VOLTAGE REGULATOR:
• Low Radiator Level •Engine under speed '/s% Voltage regulation • EMI filter • Under-speed
• Three auxiliary alarms •Over&under voltage protection•Over-excitation protection•total encapsulation
•Battery fail alarm
Also included is tamper-proof engine hour meter DC ELECTRICAL SYSTEM:
ENGINE• Battery tray • Battery cables • Battery hold down straps
Full flow oil filter • Air filter • Oil pump • Solenoid type • 2-stage battery float charger with maintaining &
starter motor•Hi-temp radiator•Jacket water pump recharging automatic charge stages.
•Thermostat•Pusher fan and guard•Exhaust manifold WEATHER/SOUND PROOF ALUMINUM HOUSING
• 12 VDC battery charging alternator • Flexible exhaust CORROSION RESISTANT PROTECTION CONSISTING OF:
connector • "Isochronous" duty, electronic governor • .9 Heated And Agitated Wash Stages
Secondary dry fuel regulator • Dry fuel lock-off solenoid • •Zinc Phosphate Etching-coating Stage
Vibration isolators • Closed coolant recovery system with .Final Baked On Enamel Powder Coat
50150 water to anti-freeze mixture • flexible oil & radiator . 18/8 Stainless Steel Hardware
drain hose.
Design & specifications subject to change
without prior notice. Dimensions shown are
approximate. Contact Gillette for certified
drawings.
DO NOT USE DIMENSIONS FOR
INSTALLATION PURPOSES.
Q
z
w
w
z
z
w
F�-- 48 1/4 ---
71 3i8
• m
-- p. —_
o
4 Gillette Generators,Inc.9 2921 Thorne Dr.*Elkhart,IN•46514 9 Ph:574-264-9639-Fax:574-262-1840•Web:www.gillettegenerators.com 9 spc4-221103
a v0 1
v
G�� F�•w_—a'1^� rr � x e` t O i 0• ��;C O C= �;�. ` :.. �� f u
ID xXx r. 7T, � 3= 3 T r, c r _ € r F, ,� 0)
u..,. ace �s: .• � _Lc � s>p� K T �• i—x•... —a i IJ— ..t F: �' #•
we y s z i :3 3 X
L J.Mott.PEA ,w,ati _ >f f _ ( —
3 = a —•7 } ram•' }{
T s'e
�eMbG-.<�� 7 �/ � ~' �_ 3•T ' _ � � �� if=1-��
S
i
f
.�. r e. .3
� a T5 � rrt. � �, =_�.� �3�i•'._ ,i. �lV_.c.«'S .'r -: �G � f E �' r
f Ut
L .y � L v. is •� -f. : l � 3u�%was �s m a�F�•�. (( ma �:
R.
�Fr R r � �y. f. �i � s ,3 S�? � ? �/i t«..•'a� � 7' oeioe —m m:oe; � ;n
G G ;/ ''='1 R � tl• _ _ a f• a :a,;c�'c �T a :may R �
c
F—i-- _
s
� m _• a —3 � � x n �� tS sa
RT7cp
cz
r- 2
N1 DP 3c ^y> !. G
Tm .a Np m
p p
f
p C V CL
a ao c� v
ZABATT
POWER SYSTEMS
4612 Highway Avenue
Jacksonville,Florida 32254
Tel: 904 384 4505
August 20,2024 Fax: 904 384 9915
www.zabatt.com
To: Village of Tequesta City Hall Emergency Standby Project
Bid#: RFP-PW-03-05-2024Schedule Time Line
Timellne Scheduling Estimates, 08/20/2024
• Village of Tequesta awards project.
• Village of Tequesta assigns contract or PO to initiate project.
• Project process starts.
• Zabatt Assembles Engineering team as required in bid RFP. Estimated 6-8 weeks,
(Exception: Electrical Engineering 2 weeks, allowing the release to order equipment)
• Engineering team reviews, assembles and provides Stamped and Certified drawings for the
purpose of Plumbing, Mechanical, Electrical, Structural and Civil and permit submittals.
Estimate time 6-8 weeks.
• Plans provided to Village Building Department for Permitting. Estimated time 4-6 weeks
(assuming fast tracking for city project).
• Upon receiving electrical engineered drawings approved Submittals from EngineerNillage,
Zabatt orders Equipment.
1. Estimated lead time for generator, 8-12 weeks
2. Estimated lead time for ATS, 18-20 Weeks.
• Ground breaking to Substantial completion.
a) Initial 30 days for site prep, including excavation,tank(s) burial, Generator and ATS
Pads, Setting od ATS, conduit burial.
b) Power outage for one weekend (Sat./Sun.) midway through the eight(8)week period.
c) Final 30 days for equipment placement
d) Equipment tie-ins.
e) Site restoration.*
f) Startup
g) On site system testing
h) Post project survey.
Estimated Time: 8 weeks.
*Zabatt recommends additional Bollards beyond the three tank and three generator(Six total)
required by the plan drawings in the Bid. In addition to the tank bollards, you may consider
the space around the tanks to be restored as curbed lawn area or curbed mulched bed area to
further protect the tanks from unintended damage.
Twenty-Four Hour Service Line
800 366 1323
We also noted that based on the footprint of the generator and structural pad,the unit could
be installed in a single parking place in an east—west configuration, Rather than north-south
as depicted in the plans to save a parking place.
Total estimated project time,from PO issue to completion is 36-40 weeks.
Regards,
�M (/iG
Tom Tietje
South Florida Outside Sales
Zabatt Power Systems, Inc.
Toll Free: 1-800-366-1323
Twenty-Four Hour Service Line
800 366 1323
LU
W
F
N
coC'
Q W
O
Na
lu